CA3 Compatible Quadrature PAS Sensor, with Split 12 Magnet Ring for Chainring Mount. Must have Steel Chainring bolts. For 74mm 5 Bbolt and 64mm 4 Bolt Cranksets.
3m Long TTL-> USB programming cable for Satiator, Baserunner, Phaserunner and Cycle Analyst.
*Note: All kits come pre-programmed, and most system behaviour is configurable with the Cycle Analyst buttons. But this cable is necessary if you plan to change more advanced controller settings or update device firmware*
Full Product Info
New Extra Slim Split Grin Twist Throttle, 36mm OD Fits Under Lever Shifters. 50cm cable length for CA3. Requires ID of Handlebar Tube 17mm or Larger. Won't Fit with Aluminum Handlebars with Thick Sidewalls.
CA3 Compatible Mini PAS Sensor with 24 Poles for Immediate Engagement. For Square Taper Spindles with at Least 5mm of Exposed Spindle. Standard 90cm Cable Length
New Extra Slim Split Grin Twist Throttle, 36mm OD Fits Under Lever Shifters. 50cm Cable Length for CA3. Requires ID of Handlebar Tube 17mm or Larger. Won't Fit with Aluminum Handlebars with Thick Sidewalls.
GMAC Clutchless Geared Hub Motor, Standard 10T (8.1 rpm/V) Winding.
GMAC Clutchless Geared Hub Motor, Fast (10.2 rpm per V) Winding.
Grin Phaserunner Field Oriented Controller, New V6 Model
Waterproof 8 pin CA-WP /9 pin Mains / 6 PAS plugs
Molded L1019 Motor Connector
90V Max and 90 A Peak Phase Currents (~45A Continuous)
Comes in Stainless Silver or Black Metal Shell
Full Product Information Page
New Model V5 Baserunner_L10 Field Oriented Motor Controller. Flat Profile Fits Many Downtube Battery Enclosures. L1019 Motor Plug. 70A Peak Phase Currents (~45-50A Continuous), for 24-52V Batteries (60V Max Input).
Click Here for detailed product info page
- Out of Stock -
Triple Bob and Hose Clamps for Secure Mounting of Hailong-01, 21700, and Reention Downtube Batteries. See Product Page for More Information
52V 20 Ah Downtube Battery in Reention DP9 Casing with Panasonic GA Cells, 40A BMS. ST3 Charge Port.Individually Discharge Tested at Grin to Ensure Capacity.
36V 4.0A Lithium Battery Charger 3 pin ST connector from ST 100-240V/C8
Super Bright (Max 1900 Lumen) Ebike Light with Handlebar Button and Hi/Low Beam Modes and Daytime Run Lights as Well. 12-60V Input Range with Reflective Cutoff Optics. Plugs Directly to Cycle Analyst.
CA3 Compatible Mini PAS Sensor with 24 Poles for Immediate Engagement. For Square Taper Spindles with at Least 5mm of Exposed Spindle. Long 120cm Cable Length for Cargo and Recumbent Bikes
Grin Phaserunner Field Oriented Controller, New V6 Model
Waterproof 8 pin CA-WP /9 pin Mains / 6 PAS plugs
Molded L1019 Motor Connector
90V Max and 90 A Peak Phase Currents (~45A Continuous)
Comes in Stainless Silver or Black Metal Shell
Full Product Information Page
48V 19 Ah Downtube Battery with Samsung 21700 50G Cells, 40A BMS, ST3 Charge Port.UN38.3 Certified for Shipping, Individually Discharge Tested at Grin to Ensure Capacity.
This simple aluminum plate with flanges allows any of our Baserunner controllers to be mounted on any flat surface. Works well especially for our Baserunner Stand Alone where all cables are from one end. Great when you are not using your Baserunner with a downtube battery. Comes with screws to attach your Baserunner to the plate. Alternatively, consider a Baserunner TubeMount.
4 Pieces of Snap Together Black Plastic Cable Raceway, 15 and 20mm Wide, 50cm long. Self Adhesive Tap Bonds to Bicycle Tube, Perfect for Hiding Cable Runs.
52V (14s) 23.5Ah triangular rigid case frame battery using Panasonic GA cells. 50A continuous BMS circuit. Ideal for use with our Phaserunner to produce fast and powerful ebike projects with extensive range. Individually Discharge Tested at Grin to Ensure Capacity.
- Out of Stock -
Magura MT5e Brake and lever. Pre-Bled. 2200mm. Flip Flop lever. Cut to length. Rotor not included.
36V 24 Ah Downtube Battery with Samsung INR21700-50G Cells, 40A BMS, ST3 Charge Port.Individually Discharge Tested at Grin to Ensure Capacity.
Excellent Deal Bottom Bracket Torque Sensor from Fischer-AG. Senses Left Crank Pedal Force Similar to THUN/NCTE and Requires Drilling Hole in Bottom Bracket for Cable Exit. 127mm Square Taper Spindle and 68mm BB Width.
Complete Torque Sensor Crankset: ERider-T17N for 73mm BB Shells with Side Cable Exit, 170mm Miranda Cranks and 4 Bolt 104mm BCD Spider with a 52T Chainring.
Click Here for detailed product info page
- Out of Stock -
Complete Torque Sensor Crankset: ERider-T17N for 68mm BB Shells with Side Cable Exit, 170mm Miranda Cranks and 4 Bolt 104mm BCD Spider with a 52T Chainring.
Click Here for detailed product info page
- Out of Stock -
48V 10 Ah Bottle Battery and Cage Mount. Panasonic GA Cells, 25A BMS. ST3 Charge Port.Individually Discharge Tested at Grin to Ensure Capacity.
36V 10 Ah Bottle Battery and Cage Mount. Panasonic GA Cells, 25A BMS. ST3 Charge Port.Individually Discharge Tested at Grin to Ensure Capacity.
24" DM30 Weinmann Double Wall Black/ Silver 30mm Wide Rim
V6 Baserunner_L10 Field Oriented Motor Controller. Flat Profile Fits Many Downtube Battery Enclosures. L1019 Motor Plug. 80A Peak Phase Currents (~45-50A Continuous), for 24-52V Batteries (60V Max Input).
Full Product Information Page
Main9 to DC 5.5mm x 2.1mm Male Adapter, 1m long. Provides Convenient Power Source for Rear Bike Lights from Unused Main9 Plug in Controllers with V3 Cycle Analyst
1 pair of Tektro HD-E350 Hydraulic Brakes with motor cut-off. Comes with 2-pin HiGo plugs.
Click Here for detailed product info page
- Out of Stock -
The kit will run with any battery pack from 24V to 52V nominal (and up to 72V with a Phaserunner). We offer a range of batteries that will work well depending on the geometry of your bike, the range you need on a charge, and how fast you want to go. Please see our battery info page for more details on the different pack options.
Be sure to select a charger model that matches the voltage (36V, 48V, or 52V) and connector style (ST3 or XLR) of the chosen pack.
Parallel Anderson Cable for Baserunners Installed in Reention Case. Simplifies Dual Controllers or Dual Battery Systems.
The Baserunner controller is ideal if you are getting a downtube battery as we will mount it inside the battery cradle. The larger Phaserunner is required if you need an option that can run up to 72V, or if you are using one of the other battery models. It will also produce slightly higher peak torque due to the 90A vs 80A max phase current.
Throttles, ebrake levers, pas sensors, and torque sensors all play a roll in how you interact with the ebike. Torque and PAS sensor automatically power the bike whenever you pedal with an assist level controlled by the CA3's MFSwitch, while a throttle gives manual control. Please see our PAS info page for more details on these options
Even if you choose a PAS or Torque sensor as the primary control, we always recommend having a throttle as well. It can be handy to accelerate in tight situations and is great as a back-up if ever the pedal sensor has issues.
Regenerative Braking can be controlled with the addition of an ebrake lever, using the throttle to modulate the signal, or it can also be activated through back-pedal crank's rotation.
There are a number of optional electronic and mechanical accessories that can help flush out the build. This includes front and rear bike lights, phone chargers, wire management, programming cables, and what have you.
52V 29Ah Fuel Tank battery (CANON I casing) with Samsung INR21700-50G Cells, 50A BMS. ST3 Charge Port. Individually Discharge Tested at Grin to Ensure Capacity. Battery does not have ON/OFF Switch
You can get a bare hub and lace it into a suitable 36 hole rim yourself, or choose to get a professional wheel build done here at Grin using our stock rim selections and quality Sapim butted spokes. Our head wheel builder Robert has decades of experience and is renowned for building wheels that are nearly bombproof.
If you want Grin to do the wheelbuild, be sure to select either the Silver or Black spoke option from the dropdown menu, along with your preferred rim. By default all wheels will be be dished with the rim dead center between the dropouts, if you require some special dishing offset for an oddball frame please mention that in the order comments.
If you are doing your own wheel build into your own rim and just require the spokes only, be sure to specify the required spoke length in the order comments to match your selected rim ERD and lacing pattern.
The V3 Cycle Analyst is an integral part of this kit system that ties together the throttle, ebrake, PAS, and torque sensor signals into a highly configurable platform that can be readily customized for a range of performance behaviors you can't get anywhere else. As a display it may look a tad clunky, but the functionality it offers is simply unparalleled and continues to increase with each new firmware release.
The GMAC motors are available in 2 different winding speeds (fast and standard) depending on how fast you need to go for a given wheel diameter and battery voltage. In most scenarios, we recommend the fast wind for 20" wheels and the standard winding speed for 26" and larger.
The included splined torque arm fits inside the dropout and fully secures the axle against both forward and reverse torque from regen.
Laser Engrave 250 Watt Continuous Power Rating on Motor Side Plate. This is Truthful. ALL Hub Motors Offered by Grin Have an Operating Point (RPM and Allowable Temperature) Where They Can Only Sustain 250W.
Phaserunner assembled with incorrectly spec'd mosfet driver, suitable for 36V packs only. *Clearance Sale* - 1 year limited warranty. Specify silver or black preference in order comments.
Click Here for detailed product info page
- Out of Stock -
36V 8.5Ah Battery Made of Three LiGo 10X Modules with Rail and Baserunner Dock for Mounting. Behaves like a 300 Wh Pack but Disassembles Into 100Wh Packs for Air Travel. ST3 Charge Port. Made in Canada and CUSMA Compliant for Duty Free USA Shipping.
36V 11Ah Battery Made of Four LiGo 10X Modules with Rail and Baserunner Dock for Mounting. Behaves like a 400 Wh Pack but Disassembles Into 100Wh Packs for Air Travel. ST3 Charge Port. Made in Canada and CUSMA Compliant for Duty Free USA Shipping.
36V 14Ah Battery Made of Five LiGo 10X Modules with Rail and Baserunner Dock for Mounting. Behaves like a 500 Wh Pack but Disassembles Into 100Wh Packs for Air Travel. ST3 Charge Port. Made in Canada and CUSMA Compliant for Duty Free USA Shipping.
36V 17Ah Battery Made of Six LiGo 10X Modules, Rail, and Baserunner Dock for Mounting. Behaves like a 600 Wh Pack but Disassembles Into 100Wh Packs for Air Travel. ST3 Charge Port. Made in Canada and CUSMA Compliant for Duty Free USA Shipping.
For Other LiGo Options (Soft Frame Bag Mount, Rail with Basic Dock for Phaserunner etc.) Use Separate LiGo Battery Module Purchase Page and Select Appropriate Hardware.
Canadian
